Ciao a tutti,<br>a casa ho un Alice Gate Wi-Fi 2 plus sul quale vorrei mettere l'Openwrt.<br><br>Allego le foto del circuito. <br><br>Procediamo con ordine.<br>La board che ho io è la AliceAGW2+, nome in codice AGA mi pare, cioé il Alice Gate wifi plus 2<br>
<br>mi sono scaricato il trunk è ho fatto le modifiche necessarie affinché la board riconosca l'immagine di openwrt.<br><br>Ho il collegamento seriale tramite un adattatore usb-uart.<br>Per flasharla di solito faccio così:<br>
- ponticello il pin RX della seriale a massa (cioé sulla board si fa un corto tra il pin 5 e 6)<br>- imposto la porta eth0 del pc su 192.168.1.100<br>- collego il cavo ethernet sulla porta 2 dell'Alice e al pc<br>- apro firefox sul <a href="http://192.168.1.1">http://192.168.1.1</a> <br>
- su apre un uploader http per le immagini<br>- scarico e upload-o l'immagine<br>- guardo su minicom l'output<br><br>Al momento ho messo su un firmware beta che si basa sul quello della US Robotics fatto da roleo<br>
più precisamente:<br><a href="http://beghiero.myftp.org/firmware/roleo/pirelli_alice_gate_2_plus_wifi%28AGA%29/fw/beta/">http://beghiero.myftp.org/firmware/roleo/pirelli_alice_gate_2_plus_wifi%28AGA%29/fw/beta/</a><br>il USRAGW2-PLUS_fs_kernel_3.04L.01.-091113_2200<br>
<br>questo è il log:<br>CFE version 1.0.37-3.1 P12 for BCM96348 (32bit,SP,BE)<br>Build Date: mar set 26 15:13:11 CEST 2006 (root@RanmaLinux)<br>Copyright (C) 2000-2005 Broadcom Corporation.<br><br>Boot Address 0xbf000000<br>
<br>Initializing Arena.<br>Initializing Devices.<br>cfi_flash_get_device_id<br>Parallel flash device: name AM29LV640MT, id 0x2201, size 8192KB<br>CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz<br>Total memory: 16777216 bytes (16MB)<br>
<br>Total memory used by CFE: 0x80401000 - 0x80525DD0 (1199568)<br>Initialized Data: 0x8041D5E0 - 0x8041F560 (8064)<br>BSS Area: 0x8041F560 - 0x80423DD0 (18544)<br>Local Heap: 0x80423DD0 - 0x80523DD0 (1048576)<br>
Stack Area: 0x80523DD0 - 0x80525DD0 (8192)<br>Text (code) segment: 0x80401000 - 0x8041D5D8 (116184)<br>Boot area (physical): 0x00526000 - 0x00566000<br>Relocation Factor: I:00000000 - D:00000000<br>
<br>Board IP address : 192.168.1.1:ffffff00 <br>Host IP address : 192.168.1.100 <br>Gateway IP address : <br>Run from flash/host (f/h) : f <br>Default host run file name : vmlinux <br>
Default host flash file name : bcm963xx_fs_kernel <br>Boot delay (0-9 seconds) : 1 <br>Boot image (0=latest, 1=previous) : 0 <br>Board Id Name : AliceAGW2+ <br>Psi size in KB : 24<br>
Number of MAC Addresses (1-32) : 13 <br>Base MAC Address : 00:19:3e:11:40:8c <br>Ethernet PHY Type : Internal<br>Memory size in MB : 16<br><br>*** Press any key to stop auto run (1 seconds) ***<br>
Auto run second count down: 1<br>web info: Waiting for connection on socket 0.<br>web info: Waiting for connection on socket 1.<br>web info: Waiting for connection on socket 0.<br>CFE> Tag pointer 808000C0<br>web info: Upload 4059618 bytes, Broadcom image format.<br>
CFE> Tag pointer 808000C0<br>CRC from tag b0888558 - CRC from image b0888558<br>pre-existent copy in partition -> 1<br>Flashing root file system and kernel at 0xbf400000<br><br>remaining to flash ....... 00061922<br>
<br>.<br>*** Image flash done *** !<br>Resetting board...<br><br><br>CFE version 1.0.37-3.1 P12 for BCM96348 (32bit,SP,BE)<br>Build Date: mar set 26 15:13:11 CEST 2006 (root@RanmaLinux)<br>Copyright (C) 2000-2005 Broadcom Corporation.<br>
<br>Boot Address 0xbf000000<br><br>Initializing Arena.<br>Initializing Devices.<br>cfi_flash_get_device_id<br>Parallel flash device: name AM29LV640MT, id 0x2201, size 8192KB<br>CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz<br>
Total memory: 16777216 bytes (16MB)<br><br>Total memory used by CFE: 0x80401000 - 0x80525DD0 (1199568)<br>Initialized Data: 0x8041D5E0 - 0x8041F560 (8064)<br>BSS Area: 0x8041F560 - 0x80423DD0 (18544)<br>
Local Heap: 0x80423DD0 - 0x80523DD0 (1048576)<br>Stack Area: 0x80523DD0 - 0x80525DD0 (8192)<br>Text (code) segment: 0x80401000 - 0x8041D5D8 (116184)<br>Boot area (physical): 0x00526000 - 0x00566000<br>
Relocation Factor: I:00000000 - D:00000000<br><br>Board IP address : 192.168.1.1:ffffff00 <br>Host IP address : 192.168.1.100 <br>Gateway IP address : <br>Run from flash/host (f/h) : f <br>
Default host run file name : vmlinux <br>Default host flash file name : bcm963xx_fs_kernel <br>Boot delay (0-9 seconds) : 1 <br>Boot image (0=latest, 1=previous) : 0 <br>Board Id Name : AliceAGW2+ <br>
Psi size in KB : 24<br>Number of MAC Addresses (1-32) : 13 <br>Base MAC Address : 00:19:3e:11:40:8c <br>Ethernet PHY Type : Internal<br>Memory size in MB : 16<br>
<br>*** Press any key to stop auto run (1 seconds) ***<br>Auto run second count down: 0<br>Booting from latest image (0xbf400000) ...<br>Code Address: 0x80010000, Entry Address: 0x801e3018<br>8192 size flash memory detected<br>
starting image at [BF400100] image length 3df0e2<br><br>CRC from tag b0888558 - CRC image calculated b0888558<br>Decompression OK!<br>Entry at 0x801e3018<br>Closing network.<br>Starting program at 0x801e3018<br>Linux version 2.6.8.1 (root@debian) (gcc version 3.4.2) #1 Fri Nov 13 22:13:04 CET 2009<br>
Parallel flash device: name AM29LV320MT, id 0x2201, size 8192KB<br>Total Flash size: 8192K with 135 sectors<br>***Board is not initialized****: Using the default PSI size: 24<br>AliceAGW2+ prom init<br>CPU revision is: 00029107<br>
mpi: No Card is in the PCMCIA slot<br>Determined physical RAM map:<br> memory: 00fa0000 @ 00000000 (usable)<br>On node 0 totalpages: 4000<br> DMA zone: 4000 pages, LIFO batch:1<br> Normal zone: 0 pages, LIFO batch:1<br>
HighMem zone: 0 pages, LIFO batch:1<br>Built 1 zonelists<br>Kernel command line: root=31:0 ro noinitrd<br>brcm mips: enabling icache and dcache...<br>Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.<br>
Primary data cache 8kB 2-way, linesize 16 bytes.<br>PID hash table entries: 64 (order 6: 512 bytes)<br>Using 128.000 MHz high precision timer.<br>Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)<br>Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)<br>
Memory: 13696k/16000k available (1622k kernel code, 2284k reserved, 241k data, 80k init, 0k highmem)<br>Calibrating delay loop... 255.59 BogoMIPS<br>Mount-cache hash table entries: 512 (order: 0, 4096 bytes)<br>Checking for 'wait' instruction... unavailable.<br>
NET: Registered protocol family 16<br>Can't analyze prologue code at 801a4274<br>SCSI subsystem initialized<br>usbcore: registered new driver usbfs<br>usbcore: registered new driver hub<br>Initializing Cryptographic API<br>
PPP generic driver version 2.4.2<br>NET: Registered protocol family 24<br>Using noop io scheduler<br>bcm963xx_mtd driver v1.0<br>PCI: Enabling device 0000:00:02.2 (0000 -> 0002)<br>ehci_hcd 0000:00:02.2: EHCI Host Controller<br>
PCI: Setting latency timer of device 0000:00:02.2 to 64<br>ehci_hcd 0000:00:02.2: irq 32, pci mem b0030000<br>ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1<br>ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 0.95, driver 2004-May-10<br>
hub 1-0:1.0: USB hub found<br>hub 1-0:1.0: 2 ports detected<br>ehci_hcd 0000:00:02.2: SCAN SetPortFeature wIndex=1 ports=2<br>ehci_hcd 0000:00:02.2: SCAN wValue =8<br>ehci_hcd 0000:00:02.2: SCAN SetPortFeature wIndex=2 ports=2<br>
ehci_hcd 0000:00:02.2: SCAN wValue =8<br>ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)<br>ohci_hcd: block sizes: ed 64 td 64<br>PCI: Enabling device 0000:00:02.0 (0000 -> 0002)<br>ohci_hcd 0000:00:02.0: OHCI Host Controller<br>
PCI: Setting latency timer of device 0000:00:02.0 to 64<br>ohci_hcd 0000:00:02.0: irq 32, pci mem b0010000<br>ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2<br>hub 2-0:1.0: USB hub found<br>hub 2-0:1.0: 1 port detected<br>
PCI: Enabling device 0000:00:02.1 (0000 -> 0002)<br>ohci_hcd 0000:00:02.1: OHCI Host Controller<br>PCI: Setting latency timer of device 0000:00:02.1 to 64<br>ohci_hcd 0000:00:02.1: irq 32, pci mem b0020000<br>ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3<br>
hub 3-0:1.0: USB hub found<br>hub 3-0:1.0: 1 port detected<br>PCI: Enabling device 0000:00:09.0 (0000 -> 0002)<br>ohci_hcd 0000:00:09.0: OHCI Host Controller<br>PCI: Setting latency timer of device 0000:00:09.0 to 64<br>
ohci_hcd 0000:00:09.0: irq 20, pci mem c0000b00<br>ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 4<br>ohci_hcd 0000:00:09.0: init err<br>ohci_hcd 0000:00:09.0: can't start<br>ohci_hcd 0000:00:09.0: init error -16<br>
ohci_hcd 0000:00:09.0: remove, state 0<br>iounmap: bad address c0000b00<br>ohci_hcd 0000:00:09.0: USB bus 4 deregistered<br>ohci_hcd: probe of 0000:00:09.0 failed with error -16<br>usbcore: registered new driver usblp<br>
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver<br>usbcore: registered new driver usbnet<br>brcmboard: brcm_board_init entry<br>Confirm button interrupt has been configured<br>bcm963xx_serial driver v2.0<br>
NET: Registered protocol family 2<br>IP: routing cache hash table of 512 buckets, 4Kbytes<br>TCP: Hash tables configured (established 512 bind 1024)<br>Initializing IPsec netlink socket<br>NET: Registered protocol family 1<br>
NET: Registered protocol family 17<br>NET: Registered protocol family 15<br>Ebtables v2.0 registered<br>NET: Registered protocol family 8<br>NET: Registered protocol family 20<br>802.1Q VLAN Support v1.8 Ben Greear <<a href="mailto:greearb@candelatech.com">greearb@candelatech.com</a>><br>
All bugs added by David S. Miller <<a href="mailto:davem@redhat.com">davem@redhat.com</a>><br>VFS: Mounted root (squashfs filesystem) readonly.<br>Freeing unused kernel memory: 80k freed<br><br>init started: BusyBox v1.00 (2009.11.13-21:16+0000) multi-call binary<br>
Algorithmics/MIPS FPU Emulator v1.5<br><br><br>BusyBox v1.00 (2009.11.13-21:16+0000) Built-in shell (ash)<br>Enter 'help' for a list of built-in commands.<br><br><br>Loading drivers and kernel modules...<br><br>atmapi: module license 'Proprietary' taints kernel.<br>
blaadd: blaa_detect entry<br>adsl: adsl_init entry<br>Broadcom BCMPROCFS v1.0 initialized<br>Broadcom BCM6348B0 Ethernet Network Device v0.3 Mar 22 2006 13:46:12<br>Config Internal PHY Through MDIO<br>BCM63xx_ENET: Auto-negotiation timed-out<br>
BCM63xx_ENET: 10 MB Half-Duplex (assumed)<br>eth0: MAC Address: 00:19:3E:11:40:8C<br>Broadcom BCM6348B0 Ethernet Network Device v0.3 Mar 22 2006 13:46:12<br>Config Ethernet Switch Through SPI Slave Select 0<br>eth1: MAC Address: 00:19:3E:11:40:8D<br>
dgasp: kerSysRegisterDyingGaspHandler: eth1 registered<br>Broadcom BCM6348B0 USB Network Device v0.4 May 16 2006 15:44:12<br>usb0: MAC Address: 00 19 3E 11 40 8E<br>usb0: Host MAC Address: 00 19 3E 11 40 8F<br>PCI: Setting latency timer of device 0000:00:01.0 to 64<br>
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)<br>wl: srom not detected, using main memory mapped srom info (wombo board)<br>wl0: wlc_attach: using main board MAC address base in NVRAM (wombo board)<br>wl0 MAC Address: 00:19:3E:11:40:90<br>
wl0: Broadcom BCM4318 802.11 Wireless Controller 3.131.35.0.cpe0.0<br>dgasp: kerSysRegisterDyingGaspHandler: wl0 registered<br>fuse init (API version 7.5)<br>fuse distribution version: 2.5.3<br>eth1 Link UP.<br>Initializing USB Mass Storage driver...<br>
usbcore: registered new driver usb-storage<br>USB Mass Storage support registered.<br>wlctl: wlctl: BcmAdsl_Initialize=0xC0058218, g_pFnNotifyCallback=0xC006DB14<br>pSdramPHY=0xA0FFFFF8, 0xDEFEFFDD 0xDDFFFEFD<br>AdslCoreHwReset: AdslOemDataAddr = 0xA0FF68B0<br>
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered<br>ip_tables: (C) 2000-2002 Netfilter core team<br>ip_conntrack version 2.1 (125 buckets, 0 max) - 368 bytes per conntrack<br>ip_conntrack_pptp version 2.1 loaded<br>
ip_nat_pptp version 2.0 loaded<br>ip_conntrack_h323: init<br>ip_nat_h323: initialize the module!<br>Executing adslctl...<br>ip_conntrack_rtsp v0.01 loading<br>adslctl configuration done<br>ip_nat_rtsp v0.01 loading<br><br>
==> Bcm963xx Software Version: 1350_032206-3.04L.01.A2pB020a.d17f <==<br><br>device usb0 entered promiscuous mode<br>br0: port 1(usb0) entering learning state<br>br0: topology change detected, propagating<br>br0: port 1(usb0) entering forwarding state<br>
device eth0 entered promiscuous mode<br>br0: port 2(eth0) entering learning state<br>br0: topology change detected, propagating<br>br0: port 2(eth0) entering forwarding state<br>device eth1 entered promiscuous mode<br>br0: port 3(eth1) entering learning state<br>
br0: topology change detected, propagating<br>br0: port 3(eth1) entering forwarding state<br>Country stored in PSI is IT<br>Setting SSID "USR9108"<br>wlctl: Not Found<br>SIOCGIFFLAGS: No such device<br>Setting country code using abbreviation: "IT"<br>
wlctl: wl0 current channel 11<br>device wl0 entered promiscuous mode<br>br0: port 4(wl0) entering learning state<br>br0: topology change detected, propagating<br>br0: port 4(wl0) entering forwarding state<br>device wl0.1 entered promiscuous mode<br>
421 Unable to open configuration file.<br>br0: port 2(eth0) entering disabled state<br>br0: port 1(usb0) entering disabled state<br>Setting ip_conntrack...<br>Verifying rsitree...<br>rsitree found<br>rsitree modified<br>rsitree check done<br>
Starting mini_httpd...<br>Configuring Extra Settings web pages access...<br>Configuring udhcpd...<br>udhcpd configuration done<br>Restarting udhcpd...<br>Configuring bftpd...<br>ftpd configuration done<br>Restarting bftpd...<br>
killall: bftpd: no process killed<br>Configuring samba...<br>Missing parameters<br>killall: smbd: no process killed<br>killall: nmbd: no process killed<br>cat: /var/samba/samba_enabled: No such file or directory<br>test: 1: unknown operand<br>
Configuring antenna diversity<br>antenna diversity configuration done<br>Executing p910nd<br>Missing parameters<br>Executing webcam_server<br>Missing parameters<br>Executing profile script...<br>Missing parameters<br>Starting custom programs...<br>
<br><br>Questo kernel ha un bel po' di servizi: tipo ftpd, print server ecc.<br><br>mentre se carico su un firmware fatto da me con openwrt mi crash-a, con il seguente log:<br>CFE version 1.0.37-3.1 P12 for BCM96348 (32bit,SP,BE)<br>
Build Date: mar set 26 15:13:11 CEST 2006 (root@RanmaLinux)<br>Copyright (C) 2000-2005 Broadcom Corporation.<br><br>Boot Address 0xbf000000<br><br>Initializing Arena.<br>Initializing Devices.<br>cfi_flash_get_device_id<br>
Parallel flash device: name AM29LV640MT, id 0x2201, size 8192KB<br>CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz<br>Total memory: 16777216 bytes (16MB)<br><br>Total memory used by CFE: 0x80401000 - 0x80525DD0 (1199568)<br>
Initialized Data: 0x8041D5E0 - 0x8041F560 (8064)<br>BSS Area: 0x8041F560 - 0x80423DD0 (18544)<br>Local Heap: 0x80423DD0 - 0x80523DD0 (1048576)<br>Stack Area: 0x80523DD0 - 0x80525DD0 (8192)<br>
Text (code) segment: 0x80401000 - 0x8041D5D8 (116184)<br>Boot area (physical): 0x00526000 - 0x00566000<br>Relocation Factor: I:00000000 - D:00000000<br><br>Board IP address : 192.168.1.1:ffffff00 <br>
Host IP address : 192.168.1.100 <br>Gateway IP address : <br>Run from flash/host (f/h) : f <br>Default host run file name : vmlinux <br>Default host flash file name : bcm963xx_fs_kernel <br>
Boot delay (0-9 seconds) : 1 <br>Boot image (0=latest, 1=previous) : 0 <br>Board Id Name : AliceAGW2+ <br>Psi size in KB : 24<br>Number of MAC Addresses (1-32) : 13 <br>Base MAC Address : 00:19:3e:11:40:8c <br>
Ethernet PHY Type : Internal<br>Memory size in MB : 16<br><br>*** Press any key to stop auto run (1 seconds) ***<br>Auto run second count down: 0<br>Booting from latest image (0xbf010000) ...<br>
Code Address: 0x80010000, Entry Address: 0x80010000<br>8192 size flash memory detected<br>starting image at [BF010100] image length 33ff04<br><br>CRC from tag b974d0f7 - CRC image calculated b974d0f7<br>Decompression OK!<br>
Entry at 0x80010000<br>Closing network.<br>Starting program at 0x80010000<br>Linux version 2.6.30.10 (joskic@joskic-laptop) (gcc version 4.3.3 (GCC) ) #2 Sun Jan 17 20:07:42 CET 2010<br>Detected Broadcom 0x6348 CPU revision b0<br>
CPU frequency is 256000000 Hz<br>16MB of RAM installed<br>registering 37 GPIOs<br>board_bcm963xx: CFE version: 1.0.37-3.1<br>console [early0] enabled<br>CPU revision is: 00029107 (Broadcom BCM6348)<br>board_bcm963xx: board name: AliceAGW2+<br>
Determined physical RAM map:<br> memory: 01000000 @ 00000000 (usable)<br>Initrd not found or empty - disabling initrd<br>Zone PFN ranges:<br> Normal 0x00000000 -> 0x00001000<br>Movable zone start PFN for each node<br>
early_node_map[1] active PFN ranges<br> 0: 0x00000000 -> 0x00001000<br>Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064<br>Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200<br>
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.<br>Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes<br>NR_IRQS:128<br>PID hash table entries: 64 (order: 6, 256 bytes)<br>Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)<br>
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)<br>Memory: 13268k/16384k available (2073k kernel code, 3116k reserved, 428k data, 132k init, 0k highmem)<br>Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)<br>
Mount-cache hash table entries: 512<br>net_namespace: 532 bytes<br>NET: Registered protocol family 16<br>registering PCI controller with io_map_base unset<br>bio: create slab <bio-0> at 0<br>pci 0000:00:02.0: PME# supported from D1 D3hot D3cold<br>
pci 0000:00:02.0: PME# disabled<br>pci 0000:00:02.1: PME# supported from D1 D3hot D3cold<br>pci 0000:00:02.1: PME# disabled<br>pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot D3cold<br>pci 0000:00:02.2: PME# disabled<br>
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)<br>ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0<br>NET: Registered protocol family 2<br>IP route cache hash table entries: 1024 (order: 0, 4096 bytes)<br>
TCP established hash table entries: 512 (order: 0, 4096 bytes)<br>TCP bind hash table entries: 512 (order: -1, 2048 bytes)<br>TCP: Hash tables configured (established 512 bind 512)<br>TCP reno registered<br>NET: Registered protocol family 1<br>
audit: initializing netlink socket (disabled)<br>type=2000 audit(0.352:1): initialized<br>squashfs: version 4.0 (2009/01/31) Phillip Lougher<br>Registering mini_fo version $Id$<br>JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.<br>
msgmni has been set to 25<br>alg: No test for stdrng (krng)<br>io scheduler noop registered<br>io scheduler deadline registered (default)<br>gpiodev: gpio device registered with major 254<br>gpiodev: gpio platform device registered with access mask FFFFFFFF<br>
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart<br>console handover: boot [early0] -> real [ttyS0]<br>bcm63xx_enet MII bus: probed<br>bcm963xx_flash: 0x01000000 at 0x1f000000<br>bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank<br>
Data bus error, epc == 8017647c, ra == 8017679c<br>Oops[#1]:<br>Cpu 0<br>$ 0 : 00000000 10008400 bf800020 00800020<br>$ 4 : 00000001 00000002 00000001 00000002<br>$ 8 : 00000002 00000001 00000001 8027b110<br>$12 : 00800000 00000000 00000000 00000000<br>
$16 : 8027b110 00800000 80323d70 00800000<br>$20 : 80323d70 80c1f380 80c1f380 8027b110<br>$24 : 00000018 80188770 <br>$28 : 80322000 80323cf0 00000000 8017679c<br>Hi : 00000000<br>Lo : 00000002<br>
epc : 8017647c 0x8017647c<br> Not tainted<br>ra : 8017679c 0x8017679c<br>Status: 10008403 KERNEL EXL IE<br>Cause : 0080001c<br>PrId : 00029107 (Broadcom BCM6348)<br>Modules linked in:<br>Process swapper (pid: 1, threadinfo=80322000, task=80321928, tls=00000000)<br>
Stack : 10008403 00000000 000000aa 00000051 00000052 00000059 0000002c 80323d68<br> 00000002 00000025 00000001 80323d70 8027b110 801758b8 80322000 8024c8d0<br> 00000001 00000010 00000000 00000010 00000001 80323d70 00000001 80323d70<br>
8027ae88 80c1f380 00000002 80186f34 80321928 80270000 7fffffff 00000000<br> 00000000 00000000 00000001 00000002 00000001 00000000 00000000 00000000<br> ...<br>Call Trace:[<801758b8>] 0x801758b8<br>
[<80186f34>] 0x80186f34<br>[<801757f0>] 0x801757f0<br>[<80188858>] 0x80188858<br>[<800e76ec>] 0x800e76ec<br>[<800b2bf4>] 0x800b2bf4<br>[<800e8a34>] 0x800e8a34<br>[<801631bc>] 0x801631bc<br>
[<8012c794>] 0x8012c794<br>[<80163300>] 0x80163300<br>[<8012ce70>] 0x8012ce70<br>[<80163294>] 0x80163294<br>[<80162940>] 0x80162940<br>[<8012cf00>] 0x8012cf00<br>[<801620a0>] 0x801620a0<br>
[<80029a40>] 0x80029a40<br>[<802920a8>] 0x802920a8<br>[<801636b0>] 0x801636b0<br>[<80292004>] 0x80292004<br>[<802920a8>] 0x802920a8<br>[<8001b680>] 0x8001b680<br>[<80063828>] 0x80063828<br>
[<80291b10>] 0x80291b10<br>[<80282304>] 0x80282304<br>[<8001e100>] 0x8001e100<br><br><br>Code: 24020004 8d62000c 00431021 <94420000> 0805d927 3042ffff 55020005 afa20000 8d62000c<br>Disabling lock debugging due to kernel taint<br>
Kernel panic - not syncing: Attempted to kill init!<br><br>ps. inoltre sul sito <a href="http://beghiero.myftp.org/firmware/roleo/">http://beghiero.myftp.org/firmware/roleo/</a> ci sono un paio di cose utili: tipo come aggiungere la seconda usb.<br>
<br><br>Qualcuno ha qualche idea? il mio scopo è di far funzionare su questo router anche le pennine UMTS.<br><br>Ciao a tutti<br>Aljosa<br>