[Ninux-Wireless] Fwd: [OpenWrt-Devel] Adding support to a BCM96348 device

Mer 6 Apr 2011 11:20:59 CEST

OT. ma se un router (netgear) non è presente nella lista... ci sono 
altre alternative?

On 04/06/11 11:11, Claudio wrote:
> Ciao Marco, ciao tutti
> questa mail spiega come integrare una nuovo router dentro openwrt.
> E' proprio la domanada a cui spesso capita di rispondere, non ultimo
> Marco ieri sera.
>
> Riporto la mail centrale ma vi consiglio di seguire tutto il trhead.
>
> ---------- Forwarded message ----------
> From: Roger Hardiman<roger a rjh.org.uk>
> Date: 2011/4/2
> Subject: Re: [OpenWrt-Devel] Adding support to a BCM96348 device
> To: OpenWrt Development List<openwrt-devel a lists.openwrt.org>, carbaior a upv.es
>
>
> Carlos,
>
>
>
> I think you will need to make two changes to OpenWRT to make your board work.
>
> I will explain the changes to the source code that will need to be
> made at the end of the email.
>
>
>
> However for now there is an easy thing you can do.
>
>
>
> 1) keep your board set to the board name of 96348GW-10
>
> 2) flash the firmware from CFE
>
> 3) once the firmware is booted and you have the linux shell, type in
> this command
>
>                        mtd fix
>
>
>
> This re-calculates the checksum and stores it in the flash memory.
>
> This should then mean that when you next reboot, CFE will not have a
> checksum error.
>
>
>
>
>
>
>
>
>
> To make the board supported by OpenWRT all the time, three things are needed
>
> 1) the file target/linux/brcm63xx/base-files/etc/uci-defaults/brcm63xx_fixcrc.sh
> needs to be modified.
>
> This file runs once, when the router first boots after flashing
> firmware. The script then gets erased so it only runs once.
>
> You need to change this line
>
> "bcm63xx/CPVA642 "* | "bcm63xx/MAGIC "*)
>
> to say this
>
> "bcm63xx/CPVA642 "* | "bcm63xx/MAGIC "* | "bcm63xx/CPVA502+ "* )
>
>
>
> 2) in the Linux kernel source is this file
> arch/mips/bcm63xx/boards/board_bcm963xx.c
>
> For testing, you need to edit this file and add in a new board_id.
> Look for how the 96348GW-10 is defined and copy and paste. The
> board_name needs to become CPVA502+. Everything else can stay the
> same.
>
> You can then re-compile OpenWRT and test this change.
>
>
>
> 3) if everything works we need to make a patch file for the change to
> board_bcm963xx.c and add this to the OpenWRT target source tree so
> that everyone else building openWRT will get the linux kernel patched
> with the new board_id.
>
>
>
>
>
> Let me know if you need any help.
>
> I’ve just done all these steps for the BT Voyager 2500V (RTA1046)
> router including the mtd fix
>
>
>
>
>
> Roger
>
> --
>
> Roger Hardiman
>
> Technical Consultant
>
> Optimum Security Services Ltd
>
> Mobile 07968 245759
>
> Office 0870 350 2171
>
> Email roger.hardiman a optimum.me.uk
>
>
>
> -----Original Message-----
> From: openwrt-devel-bounces a lists.openwrt.org
> [mailto:openwrt-devel-bounces a lists.openwrt.org] On Behalf Of Carlos
> Baiget
> Sent: 01 April 2011 20:40
> To: OpenWrt Development List
> Subject: Re: [OpenWrt-Devel] Adding support to a BCM96348 device
>
>
>
> Hello All,
>
> Without really knowing what I was doing, I changed the board id. in
> CFE from CPVA502+ (default) to 96348GW-10 and OpenWrt booted
> (openwrt-96348GW-generic-squashfs-cfe.bin from 10.03.1-rc4)
>
> At first I had access only from serial console, but after bringing
> down the br-lan device and giving a valid ip address to eth0 I could
> connect to LuCI, enable wifi, etc.
>
> Problem: After reboot, CRC for image a partition [1] is bad and CFE
> erases it. (dump below)
>
>
>
> So most of the hardware is supported by OpenWrt but seems like it is
> neccesary to create some kind of profile for the particularities of
> CPVA502+ (original board id).
>
> Please could someone point me if i'm on a good path and how I should
> try to do that?
>
> Thank you,
> Carlos
>
> 1-CFE dump after reboot:
>
> CFE version 1.0.37-3.6 for BCM96348 (32bit,SP,BE)
>
> Build Date: ven lug 21 09:44:42 CEST 2006
>
> (oliale a oliale.telsey.loc)
>
> Copyright (C) 2003,2004,2005 Telsey Telecommunications.
>
> Boot Address 0xbfc00000
>
> Initializing Arena.
>
> Initializing Devices.
>
> Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
>
> 100 MB Full-Duplex (auto-neg)
>
> Check consistency for image tag [1]:
>
> Image CRC failed. Corrupted image at partition [1]?
>
> Calculated
>
> CRC 0x5cfa39cb. TAG CRC 0x2722a5a9.
>
> Image length 2686724.
>
> Erasing tag at partition [1] address 0xbfc10000!
>
> .
>
> Check consistency for image tag [2]: No image found at partition [2]
>
> ** Image information not found. **
>
> CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
>
> Total memory:
>
> 16777216 bytes (16MB)
>
> Total memory used by CFE: 0x80401000 - 0x80526FA0 (1204128)
>
> Initialized Data: 0x8041E610 - 0x80420480 (7792)
>
> BSS Area: 0x80420480 - 0x80424FA0 (19232)
>
> Local Heap: 0x80424FA0 - 0x80524FA0 (1048576)
>
> Stack Area: 0x80524FA0 - 0x80526FA0 (8192)
>
> Text (code) segment: 0x80401000 - 0x8041E60C (120332)
>
> Boot area (physical): 0x00527000 - 0x00567000
>
> Relocation Factor: I:00000000 - D:00000000
>
> Board IP address : 192.168.1.1:ffffff00
>
> Host
>
> IP address : 192.168.1.100
>
> Gateway IP address :
>
> Run from flash/host (f/h) : f
>
> Default host run file name : vmlinux
>
> Default host flash file name : bcm963xx_fs_kernel
>
> Boot delay (0-9 seconds) : 1
>
> Board Id Name : 96348GW-10
>
> Psi size in KB : 24
>
> Number of MAC Addresses (1-32) : 8
>
> Base MAC Address : 00:30:ab:00:00:01
>
> Ethernet PHY Type : Internal
>
> Memory size in MB : 16
>
> mac server test........................
>
> CFE>
>
>
>
>
>
>
>
> CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
>
> Total memory: 16777216 bytes (16MB)
>
> Total memory used by CFE: 0x80401000 - 0x80526FA0 (1204128)
>
> Initialized Data: 0x8041E610 - 0x80420480 (7792)
>
> BSS Area: 0x80420480 - 0x80424FA0 (19232)
>
> Local Heap: 0x80424FA0 - 0x80524FA0 (1048576)
>
> Stack Area: 0x80524FA0 - 0x80526FA0 (8192)
>
> Text (code) segment: 0x80401000 - 0x8041E60C (120332)
>
> Boot area (physical): 0x00527000 - 0x00567000
>
> Relocation Factor: I:00000000 - D:00000000
>
>
> El 31/03/11 20:29, Carlos Baiget escribió:
>
> Hello all,
>
> I'm new to Open-Wrt and I'm interested in adding support to a
> BCM9348 device currently seems unsupported.
>
> The device is an
> adsl-voip router called Telsey CPVA502+ which runs linux. I
> don't mind giving up adsl or h323 voip when using OpenWrt, but
> would like to use it as a wireless router.
>
> I've downloaded
> openwrt-96348GW-generic-squash-cfe.bin (and many others) which
> the router accepts and flashes but gives kernel panic on reboot
> (not syncing: unable to detect bcm963xx board,
> serial dump below)
>
> Following the steps found at
> http://wiki.openwrt.org/doc/devel/hw.hacking.first.steps now I
> have access to serial port but will need help on gathering
> information about hardware and probably further steps.
>
> For now I know it has:
>
> 4Mb Flash, 16Mb RAM,
> CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
>
>
> Any hint that could
> guide me to the point where OpenWrt works on this device would
> be appreciated.
>
> Greetings,
>
> Carlos
>
> *
>
> *1- Serial dump booting from -Openwrt-
>
> ****
>
> CFE version 1.0.37-3.6
> for BCM96348 (32bit,SP,BE)
>
> Build Date: ven lug 21
> 09:44:42 CEST 2006 (oliale a oliale.telsey.loc)
>
> Copyright (C)
> 2003,2004,2005 Telsey Telecommunications.
>
> Boot Address
> 0xbfc00000
>
> Initializing Arena.
>
> Initializing Devices.
>
> Parallel flash device:
> name MX29LV320AT, id 0x22a7, size 4096KB
>
> 100 MB Full-Duplex
> (auto-neg)
>
> Check consistency for
> image tag [1]:
>
> Found good image at
> partition [1]
>
> Check consistency for
> image tag [2]: No image found at partition [2]
>
> CPU type 0x29107:
> 256MHz, Bus: 128MHz, Ref: 32MHz
>
> Total memory: 16777216
> bytes (16MB)
>
> Total memory used by
> CFE: 0x80401000 - 0x80526FA0 (1204128)
>
> Initialized Data:
> 0x8041E610 - 0x80420480 (7792)
>
> BSS Area: 0x80420480 -
> 0x80424FA0 (19232)
>
> Local Heap: 0x80424FA0
> - 0x80524FA0 (1048576)
>
> Stack Area: 0x80524FA0
> - 0x80526FA0 (8192)
>
> Text (code) segment:
> 0x80401000 - 0x8041E60C (120332)
>
> Boot area (physical):
> 0x00527000 - 0x00567000
>
> Relocation Factor:
> I:00000000 - D:00000000
>
> Board IP address :
> 192.168.1.1
>
> Host IP address :
> 192.168.1.100
>
> Gateway IP address :
>
> Run from flash/host
> (f/h) : f
>
> Default host run file
> name : vmlinux
>
> Default host flash
> file name : bcm963xx_fs_kernel
>
> Boot delay (0-9
> seconds) : 1
>
> Board Id Name :
> CPVA502+
>
> Psi size in KB : 24
>
> Number of MAC
> Addresses (1-32) : 8
>
> Base MAC Address :
> 00:30:ab:00:00:01
>
> Ethernet PHY Type :
> Internal
>
> Memory size in MB : 16
>
> mac server
> test........................
>
> ###
>
> ### Find default mac
> address ,try to connect to mac server to replace it
>
> assign_MAC_addr cmd id
> 1 send packet retries #1 send
>
> ..
> ..
>
> assign_MAC_addr cmd id
> 1 send packet retries #10 send
>
> ### 00 30 ab 00 00 01
>
> *** Press any key to
> stop auto run (1 seconds) ***
>
> Auto run second count
> down: 1
>
> Code Address: 0x80010000, Entry Address: 0x80010000
>
> Decompression OK!
>
> Entry at 0x80010000
>
> Closing network.
>
> Starting program at
> 0x80010000
>
> Linux version
> 2.6.35.11 (buildbot a tksite.gotdns.org) (gcc version 4.5.2
> (Linaro GCC 4.5-2011.02-0) ) #1 Tue Mar 29 08:41:19 CDT 2011
>
> Detected Broadcom
> 0x6348 CPU revision b0
>
> CPU frequency is 256
> MHz
>
> 16MB of RAM installed
>
> registering 37 GPIOs
>
> board_bcm963xx: CFE
> version: 1.0.37-3.6
>
> board_bcm963xx:
> unknown bcm963xx board: CPVA502+
>
> bootconsole [early0]
> enabled
>
> CPU revision is:
> 00029107 (Broadcom BCM6348)
>
> Kernel panic - not
> syncing: unable to detect bcm963xx board
>
>
>
> *
>
> *2- Serial dump booting from -Original Firmware- (CFE omitted):
>
> ****
>
> *** Press any key to stop auto run (1 seconds) ***
> Auto run second count down: 0
> Code Address: 0x80010000, Entry Address: 0x801a4018
> Decompression OK!
> Entry at 0x801a4018
> Closing network.
> Starting program at 0x801a4018
> Linux version 2.6.8.1 (carpao a carpao) (gcc version 3.4.2) #2 Tue Feb
> 19 17:24:19 CET 2008
> Parallel flash device: name MX29LV320AT, id 0x22a7, size 4096KB
> Total Flash size: 4096K with 71 sectors
> CPVA502+ prom init
> CPU revision is: 00029107
> Determined physical RAM map:
>   memory: 00fa0000 @ 00000000 (usable)
> On node 0 totalpages: 4000
>    DMA zone: 4000 pages, LIFO batch:1
>    Normal zone: 0 pages, LIFO batch:1
>    HighMem zone: 0 pages, LIFO batch:1
> Built 1 zonelists
> Kernel command line: root=31:0 ro noinitrd
> brcm mips: enabling icache and dcache...
> Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
> Primary data cache 8kB 2-way, linesize 16 bytes.
> PID hash table entries: 64 (order 6: 512 bytes)
> Using 128.000 MHz high precision timer.
> Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
> Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
> Memory: 13992k/16000k available (1326k kernel code, 1988k reserved,
> 285k data, 72k init, 0k highmem)
> Calibrating delay loop... 255.59 BogoMIPS
> Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
> Checking for 'wait' instruction...  unavailable.
> NET: Registered protocol family 16
> Can't analyze prologue code at 8015a264
> PPP generic driver version 2.4.2
> NET: Registered protocol family 24
> Using noop io scheduler
> bcm963xx_mtd driver v1.0
> bcm963xx_mtd: rootfs_addr = 0xBFC10100, kernel_addr = 0xBFEBF100
> brcmboard: brcm_board_init entry
> A confirm button interrupt is not configured on this board
> CPU monitor calibration
> Calibration loops: 51030249
> bcm963xx_serial driver v2.0
> NET: Registered protocol family 2
> IP: routing cache hash table of 512 buckets, 4Kbytes
> TCP: Hash tables configured (established 512 bind 1024)
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> Ebtables v2.0 registered
> NET: Registered protocol family 8
> NET: Registered protocol family 20
> VFS: Mounted root (squashfs filesystem) readonly.
> Freeing unused kernel memory: 72k freed
> init started:  BusyBox v1.00 (2008.02.19-16:12+0000) multi-call binary
> Algorithmics/MIPS FPU Emulator v1.5
> BusyBox v1.00 (2008.02.19-16:12+0000) Built-in shell (msh)
> Enter 'help' for a list of built-in commands.
> Loading drivers and kernel modules...
> atmapi: module license 'Proprietary' taints kernel.
> blaadd: blaa_detect entry
> adsl: adsl_init entry
> Broadcom BCMPROCFS v1.0 initialized
> Broadcom BCM6348B0 Ethernet Network Device v0.3 Feb 19 2008 17:07:49
> Config Internal PHY Through MDIO
> BCM63xx_ENET: 100 MB Full-Duplex (auto-neg)
> eth0: MAC Address: 00:30:AB:00:00:01
> Broadcom BCM6348B0 Ethernet Network Device v0.3 Feb 19 2008 17:07:49
> Config External PHY Through MDIO
> mii_init: mii hardware reset
> eth0 Link UP.
> BCM63xx_ENET: Auto-negotiation timed-out
> BCM63xx_ENET: 10 MB Half-Duplex (assumed)
> eth1: MAC Address: 00:30:AB:00:00:02
> Telsey BCM6348B0 USB Network Device v0.4 Feb 19 2008 17:07:52
> usb0: MAC Address: 00 30 AB 00 00 03
> usb0: Host MAC Address: 00 30 AB 00 00 04
> Telsey CPVA502+-W, hwVer = 0xb, USB product ID set to 6310
> MAGIC USB configuration
> Endpoint: endpoint_init entry
> BOS: Enter bosInit
> Enter bosAppInit
> Exit bosAppInit
> BOS: Exit bosInit
> Endpoint: endpoint_init COMPLETED
> loading Broadcom WIFI module
> PCI: Setting latency timer of device 0000:00:01.0 to 64
> PCI: Enabling device 0000:00:01.0 (0004 ->  0006)
> wl: srom not detected, using main memory mapped srom info (wombo board)
> wl0: wlc_attach: using main board MAC address base in NVRAM (wombo board)
> wl0 MAC Address: 00:30:AB:00:00:05
> wl0: Broadcom BCM4318 802.11 Wireless Controller 3.131.35.0.cpe2.3
> dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
> wlctl: wlctl: BcmAdsl_Initialize=0xC0060228, g_pFnNotifyCallback=0xC007BFF4
> pSdramPHY=0xA0FFFFF8, 0x426B2 0xDEADBEEF
> AdslCoreHwReset: AdslOemDataAddr = 0xA0FF9014
> dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
> ip_tables: (C) 2000-2002 Netfilter core team
> ip_conntrack version 2.1 (125 buckets, 0 max) - 368 bytes per conntrack
> ip_conntrack_pptp version 2.1 loaded
> ip_nat_pptp version 2.0 loaded
> ip_conntrack_h323: init
> ip_nat_h323: initialize the module!
> insmod: cannot open module
> `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/broadcom/ip_conntrack_ipsec.ko':
> No such file or directory
> insmod: cannot open module
> `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/broadcom/ip_nat_ipsec.ko':
> No such file or directory
> insmod: cannot open module
> `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_conntrack_sip.ko':
> No such file or directory
> ==>    Bcm963xx Software Version: 3.5.8V-h323.A2pB020d.d17m<==
> device usb0 entered promiscuous mode
> app: configure ethernet eth0 speed failed.
> app: configure ethernet eth0 duplex type failed.
> br0: port 1(usb0) entering learning state
> br0: topology change detected, propagating
> br0: port 1(usb0) entering forwarding state
> device eth0 entered promiscuous mode
> br0: port 2(eth0) entering learning state
> br0: topology change detected, propagating
> br0: port 2(eth0) entering forwarding state
> app: configure ethernet eth1 speed failed.
> app: configure ethernet eth1 duplex type failed.
> device eth1 entered promiscuous mode
> br0: port 3(eth1) entering learning state
> br0: topology change detected, propagating
> br0: port 3(eth1) entering forwarding state
> Setting SSID "Telsey502plus"
> Setting SSID "Guest"
> pvc2684d: Interface "nas_0_44" created sucessfully
> pvc2684d: Communicating over ATM 0.0.44, encapsulation: LLC
> BcmNtwk_startDefDhcpSrv(990)  subnetMask = 255.255.255.0
> BcmNtwk_startDefDhcpSrv(993)  DNSServers = 192.168.1.1
> BcmNtwk_startDefDhcpSrv(996)  IPRouters = 192.168.1.1
> DHCPSRV udhcp server (v0.9.6) started
> Starting cpumond...
> Starting restorebtnd...
> BcmWan_startInterface: vpi = 0, vci = 33, conId = 1
> pWanId status = 0
> Starting the H323 application with the following parameters:
> H323 Gatekeeper address: 0.0.0.0
> H323 Gatekeeper ID:
> H323 Secondary Gatekeeper address: 0.0.0.0
> H323 Secondary Gatekeeper ID:
> H323 Gatekeeper port: 1719
> H323 Time to Live: 3600
> H323 Keep Alive Interval: 75 % of Time to Live
> H323 Terminal Type: terminal
> H323 FastStart: Off (connect)
> H323 Alias: Telsey
> H323 Alias-Pwd separator: $
> H323 Alias in setup msg: def
> Phone Line1:
> Phone Line2:
> Dialplan Line1: .t4-
> Dialplan Line2: .t4-
> Supp. Services enable mask: 0x0:0x0
> User defined Supp. Services codes:
> Call Waiting Timeout (in seconds): 15
> Override Category: Off
> Q931 T301 Timer (in seconds): 180
> Q931 T303 Timer (in seconds): 4
> Q931 T310 Timer (in seconds): 120
> No-answer timeout (in seconds): 120
> Offhook timeout (in seconds): 100
> H245 Tunneling: Off
> H245 Channel After Fast Start: Off
> Early H245: Off
> OOB DTMF: Off
> Dtmf rtp payload code: 0
> Alerting PI: 8
> Progress PI: 8
> Bearer Capability: Speech
> Plug change timeout (in seconds): Off
> H323 TOS: Off
> H323 Debugger: mode = Off --- level = ERROR
> Current global voice parameters:
> Codec G711U: Packet=20(ms) ec=On ss=Off
> Codec G711A: Packet=20(ms) ec=On ss=Off
> Codec G729: Packet=20(ms) ec=On ss=Off
> Codec priority order: G711U,G711A,G729
> Country: ITALY
> CLID signal type: FSK
> HookFlash interval: 50-150 (ms)
> On-Hook detection timeout: 250 (ms)
> Squelch inband DTMF: Off
> Fax feature: On
> Modem feature: On
> Pass through codec: Off
> NLP on Modem detection: Off
> NLP on Fax detection: On
> RTP TOS: A0
> kernel::endpoint_open
> kernel::endpoint_open COMPLETED
> slacLe9581Patch(): patch = 1
> VodslSettings::getStrParam: Set default G729 configuration parameters
> (ec and ss)
> No configured numbers ==>  NOT STARTING VODSL PROCESS
> BcmWan_startInterface: vpi = 0, vci = 44, conId = 1
> pWanId status = 0
> br0: port 3(eth1) entering disabled state
> process `snmp' is using obsolete setsockopt SO_BSDCOMPAT
> br0: port 1(usb0) entering disabled state
> main(414): pppd 2.4.1 started by admin, uid 0
>
>
>
>
>
>
>
> _______________________________________________
>
> openwrt-devel mailing list
>
> openwrt-devel a lists.openwrt.org
>
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
>
>
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel a lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
>
>
>
>
-------------- parte successiva --------------
Un allegato HTML è stato rimosso...
URL: <http://ml.ninux.org/pipermail/wireless/attachments/20110406/c1871173/attachment-0001.html>