[Ninux-Wireless] Problemi con un 841ND con openwrt
Alessandro (aka ArkaNet)
arkantiko a gmail.com
Mar 5 Ago 2014 12:40:30 CEST
Di fondo non c'è nulla di strano ... magari se fai "iw wlan0 station dump"
ti dirà pure che se collegato XD
Sarei curioso di vedere gli ultimi messaggi del dmesg
Su android prova a disabilitare il wifi e riattivarlo, se persiste rimetti
la larghezza del canale a 20Mhz e vedi come va
*--
Arka*
2014-08-05 12:17 GMT+02:00 leandro Noferini <lnoferin a cybervalley.org>:
> Luca Pretto <luca a korneolo.net> writes:
>
> > Cosa restituisce il comando "iw phy"?
>
> (Fischio) robona!
>
> root a AlCesso3:~# iw phy
> Wiphy phy0
> Band 1:
> Capabilities: 0x11ef
> RX LDPC
> HT20/HT40
> SM Power Save disabled
> RX HT20 SGI
> RX HT40 SGI
> TX STBC
> RX STBC 1-stream
> Max AMSDU length: 3839 bytes
> DSSS/CCK HT40
> Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
> Minimum RX AMPDU time spacing: 8 usec (0x06)
> HT TX/RX MCS rate indexes supported: 0-15
> Frequencies:
> * 2412 MHz [1] (27.0 dBm)
> * 2417 MHz [2] (27.0 dBm)
> * 2422 MHz [3] (27.0 dBm)
> * 2427 MHz [4] (27.0 dBm)
> * 2432 MHz [5] (27.0 dBm)
> * 2437 MHz [6] (27.0 dBm)
> * 2442 MHz [7] (27.0 dBm)
> * 2447 MHz [8] (27.0 dBm)
> * 2452 MHz [9] (27.0 dBm)
> * 2457 MHz [10] (27.0 dBm)
> * 2462 MHz [11] (27.0 dBm)
> * 2467 MHz [12] (disabled)
> * 2472 MHz [13] (disabled)
> * 2484 MHz [14] (disabled)
> Bitrates (non-HT):
> * 1.0 Mbps
> * 2.0 Mbps (short preamble supported)
> * 5.5 Mbps (short preamble supported)
> * 11.0 Mbps (short preamble supported)
> * 6.0 Mbps
> * 9.0 Mbps
> * 12.0 Mbps
> * 18.0 Mbps
> * 24.0 Mbps
> * 36.0 Mbps
> * 48.0 Mbps
> * 54.0 Mbps
> max # scan SSIDs: 4
> max scan IEs length: 2257 bytes
> Coverage class: 0 (up to 0m)
> Supported Ciphers:
> * WEP40 (00-0f-ac:1)
> * WEP104 (00-0f-ac:5)
> * TKIP (00-0f-ac:2)
> * CCMP (00-0f-ac:4)
> * CMAC (00-0f-ac:6)
> Available Antennas: TX 0x3 RX 0x3
> Configured Antennas: TX 0x3 RX 0x3
> Supported interface modes:
> * IBSS
> * managed
> * AP
> * AP/VLAN
> * WDS
> * monitor
> * mesh point
> * P2P-client
> * P2P-GO
> software interface modes (can always be added):
> * AP/VLAN
> * monitor
> valid interface combinations:
> * #{ managed, WDS, P2P-client } <= 2048, #{ IBSS, AP,
> mesh point, P2P-GO } <= 8,
> total <= 2048, #channels <= 1
> Supported commands:
> * new_interface
> * set_interface
> * new_key
> * start_ap
> * new_station
> * new_mpath
> * set_mesh_config
> * set_bss
> * authenticate
> * associate
> * deauthenticate
> * disassociate
> * join_ibss
> * join_mesh
> * remain_on_channel
> * set_tx_bitrate_mask
> * frame
> * frame_wait_cancel
> * set_wiphy_netns
> * set_channel
> * set_wds_peer
> * tdls_mgmt
> * tdls_oper
> * probe_client
> * set_noack_map
> * register_beacons
> * Unknown command (89)
> * connect
> * disconnect
> Supported TX frame types:
> * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90
> 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
> * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80
> 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
> * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90
> 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
> * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80
> 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
> * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70
> 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
> * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70
> 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
> * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80
> 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
> * (null): 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80
> 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
> Supported RX frame types:
> * IBSS: 0xb0 0xc0 0xd0
> * managed: 0x40 0xd0
> * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
> * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
> * mesh point: 0xb0 0xc0 0xd0
> * P2P-client: 0x40 0xd0
> * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
> * (null): 0x40 0xd0
> Device supports RSN-IBSS.
> HT Capability overrides:
> * MCS: ff ff ff ff ff ff ff ff ff ff
> * maximum A-MSDU length
> * supported channel width
> * short GI for 40 MHz
> * max A-MPDU length exponent
> * min MPDU start spacing
> Device supports TX status socket option.
> Device supports HT-IBSS.
>
> --
> Ciao
> leandro
> http://6xukrlqedfabdjrb.onion/blog/
> gpg fingerprint: 54A4 2612 FD50 0313 7FED 6A91 DA5C 1552 E7A4 D6C2
> "Noi di Es Toch narriamo un breve mito: all'inizio il Creatore disse
> un'immensa bugia. Perché non c'era proprio nulla, ma il Creatore parlò
> dicendo: Esiste. Ed ecco, affinché la menzogna di Dio potesse essere
> la verità di Dio, l'universo cominciò subito a esistere..."
>
>
> _______________________________________________
> Wireless mailing list
> Wireless a ml.ninux.org
> http://ml.ninux.org/mailman/listinfo/wireless
>
>
-------------- parte successiva --------------
Un allegato HTML è stato rimosso...
URL: <http://ml.ninux.org/pipermail/wireless/attachments/20140805/a925cae0/attachment-0001.html>
Maggiori informazioni sulla lista
Wireless