[IuliiNet] Firmware RB133
Luca Postregna
luca.postregna at gmail.com
Sun Jul 7 12:19:06 CEST 2013
ma su che modello di scheda stai lavorando?
2013/7/7 Filippo Madaro <filippo.madaro at gmail.com>
> Parola grossa ... utilizzato come AP e collegato al resto della rete
> tramite Ethernet; funziona.
>
> Resta da testare la modalità Mesh ed installare il secondo modulo radio e
> testarne le connettività.
>
> Operatività non funzionante verificata del modulo radio DCMA-81 Atheros è
> la funzionalità Super A/G che utilizza il canale a larghezza 40Mhz con un
> Troughput di circa 60Mbps, l'802.11e lo standard del QOS per le radio,
> inoltre ho notato che abilitando AP + WDS la Mesh smette di funzionare.
>
> Non voglio essere una PIGNA ma se lo installo sul tetto di casa voglio
> essere SUPER SICURO di non doverci tornare magari in Inverno ...
>
> Comunque funziona e lo tengo sotto test,
> ciao Filippo.
>
>
>
> Il giorno 07 luglio 2013 10:45, Luca Postregna <luca.postregna at gmail.com>ha scritto:
>
> funziona, vuol dire che non hai problemi con l'ap?
>>
>>
>> 2013/7/7 Filippo Madaro <filippo.madaro at gmail.com>
>>
>>> Ok Funziona, ora provo a montare la seconda radio e vedo se regge ... il
>>> carico
>>>
>>> root at OpenWrt:/# cat /etc/config/wireless
>>> config wifi-device radio0
>>> option type mac80211
>>> option channel 6
>>> option hwmode 11g
>>> option macaddr '00:0b:6b:22:bf:c1'
>>> # option path 'pci0000:00/0000:00:01.0'
>>> # option htmode 'HT40+'
>>> # option chanbw 20
>>> # option chanbw 5/10/20
>>> option rxantenna 1
>>> option txantenna 1
>>> option distance 2500
>>> option noscan 1
>>> # option hwmode 11bgdt
>>> option txpower 20
>>> #
>>> #
>>> #
>>> config wifi-iface
>>> option device radio0
>>> option network lan
>>> option mode ap
>>> option ifname ap0
>>> option ssid wifi.fvg.it-ap
>>> option hidden 0
>>> option isolate 0
>>> option maxassoc 10
>>> # option short_preamble 1
>>> # option wds 1
>>> option encryption none
>>> option disabled 0
>>>
>>> config wifi-iface
>>> option device radio0
>>> option network mesh
>>> # option mesh_id 67
>>> option mode adhoc
>>> option ifname adhoc0
>>> option bssid '02:aa:bb:cc:dd:ee'
>>> option ssid wifi.fvg.it-mesh
>>> option hidden 0
>>> option encryption none
>>> # option mcast_rate 30
>>> option disabled 0
>>> root at OpenWrt:/# cat /proc/loadavg
>>> 1.14 0.94 0.70 1/31 4541
>>>
>>>
>>>
>>> Il giorno 06 luglio 2013 12:50, Luca Postregna <luca.postregna at gmail.com
>>> > ha scritto:
>>>
>>> ho apportato alcune delle modifiche suggerite, a me no di non
>>>> configurare tutto a manina, cioè ogni singolo modulo, selezionando il
>>>> profilo di default per le rb1xx, vengono selezionati automaticamente i
>>>> moduli per la creazione delle vlan, quindi dobbiamo tenerci le eth1-eth4.
>>>>
>>>> Ecco i link aggiornati:
>>>>
>>>> -
>>>> https://dl.dropboxusercontent.com/u/8635572/IuliiNet/firmware/md5sums.txt
>>>> -
>>>> https://dl.dropboxusercontent.com/u/8635572/IuliiNet/firmware/openwrt-adm5120-rb1xx-rootfs.tar.gz
>>>> -
>>>> https://dl.dropboxusercontent.com/u/8635572/IuliiNet/firmware/openwrt-adm5120-rb1xx-vmlinux.elf
>>>>
>>>> A me su rb133c nessun problema con l'ap su ath5k. Questa la conf wifi:
>>>>
>>>> config wifi-device radio0
>>>> option type mac80211
>>>> option channel 11
>>>> option hwmode 11g
>>>> option path 'pci0000:00/0000:00:01.0'
>>>>
>>>> config wifi-iface
>>>> option device radio0
>>>> option network lan
>>>> option mode ap
>>>> option ifname ap0
>>>> option ssid IuliiNet
>>>> option encryption none
>>>>
>>>> config wifi-iface
>>>> option device radio0
>>>> option network wmesh
>>>> option mode adhoc
>>>> option ifname adhoc0
>>>> option bssid '02:aa:bb:cc:dd:ee'
>>>> option ssid IuliiNet-mesh
>>>> option encryption none
>>>>
>>>> @emanuele, puoi provare le immagini?
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> 2013/7/5 Filippo Madaro <filippo.madaro at gmail.com>
>>>>
>>>>> Ok testato con radio solo AP non trasmette ... quindi pezzo di
>>>>> Hardware inutile...
>>>>>
>>>>> desidero un apparato con solo Networking Bridge + BATMAN + IPV4 + IPV6
>>>>>
>>>>> dal .config toglierei la configurazione delle VLAN 802.1q, le porte
>>>>> ethernet delle RB153, il firewall, i led l'audio e la gpio, il PPP e PPPoE
>>>>>
>>>>> CONFIG_DEFAULT_admswconfig=n
>>>>> CONFIG_DEFAULT_iptables=n
>>>>> CONFIG_DEFAULT_kmod-ipt-nathelper=n
>>>>> CONFIG_DEFAULT_kmod-leds-gpio=n
>>>>> CONFIG_DEFAULT_kmod-ledtrig-adm5120-switch=n
>>>>> CONFIG_DEFAULT_kmod-pata-rb153-cf=n
>>>>> CONFIG_DEFAULT_ppp=n
>>>>> CONFIG_DEFAULT_ppp-mod-pppoe=n
>>>>> CONFIG_DEFAULT_uci=n
>>>>> CONFIG_AUDIO_SUPPORT=n
>>>>> CONFIG_GPIO_SUPPORT=n
>>>>>
>>>>> La radio di default la Ralink RT2561 ed i moduli per Atheros 5k e 9k
>>>>> ed Intel IPW-2200
>>>>>
>>>>> CONFIG_DEFAULT_kmod-rt2500-pci=y
>>>>>
>>>>> togliere tutti i moduli e supporti per la criptatura WEP WPA ecc.
>>>>>
>>>>> togliere tutti i moduli RAID , Native Language Support (solo USA), le
>>>>> Radio BroadComm, VIDEO, MAIL, DATABASE, CAPTIVE PORTAL, FILE TRANSFER solo
>>>>> wget ed scp , ASTERISK e relativi supporti, INSTANT MESSAGE, VPN, WEB,
>>>>> DIAL-IN, MULTIMEDIA
>>>>>
>>>>>
>>>>> quando hai tempo e senza fretta, grazie Filippo
>>>>>
>>>>>
>>>>>
>>>>> Il giorno 05 luglio 2013 11:55, Luca Postregna <
>>>>> luca.postregna at gmail.com> ha scritto:
>>>>>
>>>>> piuttosto che mandarmi il .config delle opzioni kernel da rimuovere,
>>>>>> se riesci fammi una lista
>>>>>>
>>>>>>
>>>>>> 2013/7/5 Luca Postregna <luca.postregna at gmail.com>
>>>>>>
>>>>>>> ok, ma scrivi in ML!
>>>>>>>
>>>>>>>
>>>>>>> 2013/7/5 Filippo Madaro <filippo.madaro at gmail.com>
>>>>>>>
>>>>>>>> Grazie Luca, il kernel gira e funziona quasi tutto, le radio
>>>>>>>> Atheros le vede subito, le radio Ralink caricando i moduli da
>>>>>>>> Attitude_Adjustment le vede, mentre per le radio Intel iwl-2/5xxx va in
>>>>>>>> Kernel Panic.
>>>>>>>> Ho caricato una configurazione Wireless con 1AP e 1Mesh con radio
>>>>>>>> Atheros e tutte le "option disabled '0'" ma non trasmette nulla, il kernel
>>>>>>>> non dà errori e carica le configurazioni correttamente, nel pomeriggio
>>>>>>>> provo ad abilitare una sola interfaccia radio AP o Client e poi ti
>>>>>>>> riferisco ...
>>>>>>>> ho notato che gzip non funziona và spesso in crash out-of-memory e
>>>>>>>> che il carico CPU è molto alto, top non mi rivela nessun carico strano
>>>>>>>> mentre loadavg inizia ad 1.8 in avvio e scende ad 1.1 dopo una decina di
>>>>>>>> minuti, normalmente con il firmware linux di mikrotik il carico CPU resta
>>>>>>>> basso se non attivi quasi nulla.
>>>>>>>> Penso che dovresti compilare ancora un kernel con solo le opzioni
>>>>>>>> indispensabili, ti mando sempre questo pomeriggio il CONFIG di quello che
>>>>>>>> ritengo indispensabile e ti faccio sapere se la radio trasmette ...
>>>>>>>>
>>>>>>>> Mandi Filippo
>>>>>>>>
>>>>>>>> ----- Messaggio originale -----
>>>>>>>> Da: "Luca Postregna" <luca.postregna at gmail.com>
>>>>>>>> A: "Filippo Madaro" <filippo.madaro at gmail.com>,
>>>>>>>> iuliinet at ml.ninux.org
>>>>>>>> Inviato: Giovedì, 4 luglio 2013 14:41:35
>>>>>>>> Oggetto: Re: Firmware RB133
>>>>>>>>
>>>>>>>>
>>>>>>>> c'era qualche problema con la branca stabile di a.a. su rb133c.
>>>>>>>> ho quindi scaricato, compilato, e testato un firmware direttamente
>>>>>>>> dal trunk.
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> *
>>>>>>>> https://dl.dropboxusercontent.com/u/8635572/IuliiNet/firmware/md5sums.txt
>>>>>>>> *
>>>>>>>> https://dl.dropboxusercontent.com/u/8635572/IuliiNet/firmware/openwrt-adm5120-rb1xx-rootfs.tar.gz
>>>>>>>> *
>>>>>>>> https://dl.dropboxusercontent.com/u/8635572/IuliiNet/firmware/openwrt-adm5120-rb1xx-vmlinux.elf
>>>>>>>>
>>>>>>>>
>>>>>>>> @filippo, fammi sapere se hai risolto, da me tutto ok
>>>>>>>>
>>>>>>>>
>>>>>>>> LP
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> 2013/7/3 Filippo Madaro < filippo.madaro at gmail.com >
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> ok e se puoi mandami una immagine del rootfs.tar.gz recente ne ho
>>>>>>>> una Kamikaze ed una Backfire ma nessuna Attitude ...
>>>>>>>>
>>>>>>>>
>>>>>>>> Grazie Filippo
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> Il giorno 03 luglio 2013 18:46, Luca Postregna <
>>>>>>>> luca.postregna at gmail.com > ha scritto:
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> uhm. io ho testato solo su rb133c, sto ricompilando le immagini,
>>>>>>>> quando è su dropbox ti avviso.
>>>>>>>> LP
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> 2013/7/3 Filippo Madaro < filippo.madaro at gmail.com >
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> Sei sicuro che vada su RB133c ??? a me dá errore compilato senza
>>>>>>>> emulazione FPU (soft-float)
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> [ 1.772000] Creating 2 MTD partitions on "gen_nand":
>>>>>>>> [ 1.780000] 0x000000000000-0x000000400000 : "kernel"
>>>>>>>> [ 1.792000] 0x000000400000-0x000004000000 : "rootfs"
>>>>>>>> [ 1.812000] mtd: partition "rootfs" set to be root filesystem
>>>>>>>> [ 1.820000] ADM5120 built-in ethernet switch driver version 0.1.1
>>>>>>>> [ 1.864000] adm5120_wdt: Watchdog Timer version 0.1
>>>>>>>> [ 1.872000] TCP cubic registered
>>>>>>>> [ 1.876000] NET: Registered protocol family 17
>>>>>>>> [ 1.880000] 8021q: 802.1Q VLAN Support v1.8
>>>>>>>> [ 1.892000] yaffs: dev is 32505859 name is "mtdblock3" ro
>>>>>>>> [ 1.896000] yaffs: passed flags ""
>>>>>>>> [ 2.744000] VFS: Mounted root (yaffs2 filesystem) readonly on
>>>>>>>> device 31:3.
>>>>>>>> [ 2.752000] Freeing unused kernel memory: 160k freed
>>>>>>>> [ 3.248000] FPU emulator disabled, make sure your toolchain was
>>>>>>>> compiled with software floating point support (soft-float)
>>>>>>>>
>>>>>>>>
>>>>>>>> la scheda é una RB112 con CPU ADM5120 se invece installo kernel +
>>>>>>>> rootfs Kamikaze vá tutto ma vorrei una versione recente tipo Attitude
>>>>>>>>
>>>>>>>>
>>>>>>>> Mandi Filippo
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> Il giorno 03 luglio 2013 17:58, Filippo Madaro <
>>>>>>>> filippo.madaro at gmail.com > ha scritto:
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> Mi manca il file system openwrt-adm5120-rb1xx-rootfs.tar.gz
>>>>>>>> ho quello vecchio della versione Kamikaze ma non l'ultimo
>>>>>>>>
>>>>>>>>
>>>>>>>> Ciao Filippo
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> Il giorno 03 luglio 2013 12:12, Luca Postregna <
>>>>>>>> luca.postregna at gmail.com > ha scritto:
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> Gdrive, Mega e simile preferisco non usarli, non dispongono di un
>>>>>>>> link diretto per il download. Diversamente, per dropbox tutto ok.
>>>>>>>>
>>>>>>>>
>>>>>>>> Ecco i files per le rb133x:
>>>>>>>>
>>>>>>>>
>>>>>>>> *
>>>>>>>> https://dl.dropboxusercontent.com/u/8635572/IuliiNet/firmware/md5sums.txt
>>>>>>>> *
>>>>>>>> https://dl.dropboxusercontent.com/u/8635572/IuliiNet/firmware/openwrt-adm5120-rb1xx-vmlinux.bin
>>>>>>>> *
>>>>>>>> https://dl.dropboxusercontent.com/u/8635572/IuliiNet/firmware/openwrt-adm5120-rb1xx-vmlinux.elf
>>>>>>>>
>>>>>>>> le istruzione per il flash delle rb133c le puoi trovare alla pagina
>>>>>>>> http://iulii.net/firmware.html#rb133c
>>>>>>>> Se non ricordo male, questi binari contengono i moduli ath5k, forse
>>>>>>>> anche ath9k. Firewall, dnsmasq, pppoe, credo di averli rimossi.
>>>>>>>> Per un buggetto nella conf di default al primo boot trovi l'esempio
>>>>>>>> per una rb1xx con 4 porte switch. Comunque, nel link sopra trovi una
>>>>>>>> configurazione funzionante per rb133c.
>>>>>>>>
>>>>>>>>
>>>>>>>> per quello che riguarda miniPCI 802.11n non ho recuperato alcun
>>>>>>>> modello. Ho solo una b/g che mi ha passato Emanuele che utilizzo con
>>>>>>>> l'antenna di un portatile.
>>>>>>>>
>>>>>>>>
>>>>>>>> Saluti
>>>>>>>> LP
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> 2013/7/3 Filippo Madaro < filippo.madaro at gmail.com >
>>>>>>>>
>>>>>>>>
>>>>>>>> Ciao Luca, ho cercato invano di scaricare i tre file per le RB133
>>>>>>>> da downloads.iulii.net ... non si apre il sito a noi poveri
>>>>>>>> sfigati IPV4 ... li puoi postare su Gdrive / Dropbox / Mega che ho un paio
>>>>>>>> di schede da flashare.
>>>>>>>>
>>>>>>>> Per le miniPCI 802.11n hai poi trovato qualcosa di compatibile
>>>>>>>> OpenWRT e con quante antenne 1/2/3 e quanti TX/RX 2T2R 3T3R ???
>>>>>>>>
>>>>>>>> Mandi Filippo
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> --
>>>>>>>>
>>>>>>>> luca.postregna.name
>>>>>>>> twitter.com/lucapost
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> --
>>>>>>>>
>>>>>>>>
>>>>>>>> p.i. Filippo Madaro
>>>>>>>>
>>>>>>>> Mob. 3883448904
>>>>>>>> Consulente DUE Energie
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> --
>>>>>>>>
>>>>>>>>
>>>>>>>> p.i. Filippo Madaro
>>>>>>>>
>>>>>>>> Mob. 3883448904
>>>>>>>> Consulente DUE Energie
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> --
>>>>>>>>
>>>>>>>> luca.postregna.name
>>>>>>>> twitter.com/lucapost
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> --
>>>>>>>>
>>>>>>>>
>>>>>>>> p.i. Filippo Madaro
>>>>>>>>
>>>>>>>> Mob. 3883448904
>>>>>>>> Consulente DUE Energie
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> --
>>>>>>>>
>>>>>>>> luca.postregna.name
>>>>>>>> twitter.com/lucapost
>>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> --
>>>>>>> luca.postregna.name
>>>>>>> twitter.com/lucapost
>>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> --
>>>>>> luca.postregna.name
>>>>>> twitter.com/lucapost
>>>>>>
>>>>>
>>>>>
>>>>>
>>>>> --
>>>>> p.i. *Filippo Madaro*
>>>>> Mob. 3883448904
>>>>> Consulente DUE Energie <http://www.dueenergie.com/index.html>
>>>>>
>>>>>
>>>>
>>>>
>>>> --
>>>> luca.postregna.name
>>>> twitter.com/lucapost
>>>>
>>>
>>>
>>>
>>> --
>>> p.i. *Filippo Madaro*
>>> Mob. 3883448904
>>> Consulente DUE Energie <http://www.dueenergie.com/index.html>
>>>
>>>
>>
>>
>> --
>> luca.postregna.name
>> twitter.com/lucapost
>>
>
>
>
> --
> p.i. *Filippo Madaro*
> Mob. 3883448904
> Consulente DUE Energie <http://www.dueenergie.com/index.html>
>
>
--
luca.postregna.name
twitter.com/lucapost
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://ml.ninux.org/pipermail/iuliinet/attachments/20130707/a3839f22/attachment-0001.htm>
More information about the IuliiNet
mailing list