[IuliiNet] Firmware RB133
Luca Postregna
luca.postregna at gmail.com
Sun Jul 7 10:45:49 CEST 2013
funziona, vuol dire che non hai problemi con l'ap?
2013/7/7 Filippo Madaro <filippo.madaro at gmail.com>
> Ok Funziona, ora provo a montare la seconda radio e vedo se regge ... il
> carico
>
> root at OpenWrt:/# cat /etc/config/wireless
> config wifi-device radio0
> option type mac80211
> option channel 6
> option hwmode 11g
> option macaddr '00:0b:6b:22:bf:c1'
> # option path 'pci0000:00/0000:00:01.0'
> # option htmode 'HT40+'
> # option chanbw 20
> # option chanbw 5/10/20
> option rxantenna 1
> option txantenna 1
> option distance 2500
> option noscan 1
> # option hwmode 11bgdt
> option txpower 20
> #
> #
> #
> config wifi-iface
> option device radio0
> option network lan
> option mode ap
> option ifname ap0
> option ssid wifi.fvg.it-ap
> option hidden 0
> option isolate 0
> option maxassoc 10
> # option short_preamble 1
> # option wds 1
> option encryption none
> option disabled 0
>
> config wifi-iface
> option device radio0
> option network mesh
> # option mesh_id 67
> option mode adhoc
> option ifname adhoc0
> option bssid '02:aa:bb:cc:dd:ee'
> option ssid wifi.fvg.it-mesh
> option hidden 0
> option encryption none
> # option mcast_rate 30
> option disabled 0
> root at OpenWrt:/# cat /proc/loadavg
> 1.14 0.94 0.70 1/31 4541
>
>
>
> Il giorno 06 luglio 2013 12:50, Luca Postregna <luca.postregna at gmail.com>ha scritto:
>
> ho apportato alcune delle modifiche suggerite, a me no di non configurare
>> tutto a manina, cioè ogni singolo modulo, selezionando il profilo di
>> default per le rb1xx, vengono selezionati automaticamente i moduli per la
>> creazione delle vlan, quindi dobbiamo tenerci le eth1-eth4.
>>
>> Ecco i link aggiornati:
>>
>> -
>> https://dl.dropboxusercontent.com/u/8635572/IuliiNet/firmware/md5sums.txt
>> -
>> https://dl.dropboxusercontent.com/u/8635572/IuliiNet/firmware/openwrt-adm5120-rb1xx-rootfs.tar.gz
>> -
>> https://dl.dropboxusercontent.com/u/8635572/IuliiNet/firmware/openwrt-adm5120-rb1xx-vmlinux.elf
>>
>> A me su rb133c nessun problema con l'ap su ath5k. Questa la conf wifi:
>>
>> config wifi-device radio0
>> option type mac80211
>> option channel 11
>> option hwmode 11g
>> option path 'pci0000:00/0000:00:01.0'
>>
>> config wifi-iface
>> option device radio0
>> option network lan
>> option mode ap
>> option ifname ap0
>> option ssid IuliiNet
>> option encryption none
>>
>> config wifi-iface
>> option device radio0
>> option network wmesh
>> option mode adhoc
>> option ifname adhoc0
>> option bssid '02:aa:bb:cc:dd:ee'
>> option ssid IuliiNet-mesh
>> option encryption none
>>
>> @emanuele, puoi provare le immagini?
>>
>>
>>
>>
>>
>> 2013/7/5 Filippo Madaro <filippo.madaro at gmail.com>
>>
>>> Ok testato con radio solo AP non trasmette ... quindi pezzo di Hardware
>>> inutile...
>>>
>>> desidero un apparato con solo Networking Bridge + BATMAN + IPV4 + IPV6
>>>
>>> dal .config toglierei la configurazione delle VLAN 802.1q, le porte
>>> ethernet delle RB153, il firewall, i led l'audio e la gpio, il PPP e PPPoE
>>>
>>> CONFIG_DEFAULT_admswconfig=n
>>> CONFIG_DEFAULT_iptables=n
>>> CONFIG_DEFAULT_kmod-ipt-nathelper=n
>>> CONFIG_DEFAULT_kmod-leds-gpio=n
>>> CONFIG_DEFAULT_kmod-ledtrig-adm5120-switch=n
>>> CONFIG_DEFAULT_kmod-pata-rb153-cf=n
>>> CONFIG_DEFAULT_ppp=n
>>> CONFIG_DEFAULT_ppp-mod-pppoe=n
>>> CONFIG_DEFAULT_uci=n
>>> CONFIG_AUDIO_SUPPORT=n
>>> CONFIG_GPIO_SUPPORT=n
>>>
>>> La radio di default la Ralink RT2561 ed i moduli per Atheros 5k e 9k ed
>>> Intel IPW-2200
>>>
>>> CONFIG_DEFAULT_kmod-rt2500-pci=y
>>>
>>> togliere tutti i moduli e supporti per la criptatura WEP WPA ecc.
>>>
>>> togliere tutti i moduli RAID , Native Language Support (solo USA), le
>>> Radio BroadComm, VIDEO, MAIL, DATABASE, CAPTIVE PORTAL, FILE TRANSFER solo
>>> wget ed scp , ASTERISK e relativi supporti, INSTANT MESSAGE, VPN, WEB,
>>> DIAL-IN, MULTIMEDIA
>>>
>>>
>>> quando hai tempo e senza fretta, grazie Filippo
>>>
>>>
>>>
>>> Il giorno 05 luglio 2013 11:55, Luca Postregna <luca.postregna at gmail.com
>>> > ha scritto:
>>>
>>> piuttosto che mandarmi il .config delle opzioni kernel da rimuovere, se
>>>> riesci fammi una lista
>>>>
>>>>
>>>> 2013/7/5 Luca Postregna <luca.postregna at gmail.com>
>>>>
>>>>> ok, ma scrivi in ML!
>>>>>
>>>>>
>>>>> 2013/7/5 Filippo Madaro <filippo.madaro at gmail.com>
>>>>>
>>>>>> Grazie Luca, il kernel gira e funziona quasi tutto, le radio Atheros
>>>>>> le vede subito, le radio Ralink caricando i moduli da Attitude_Adjustment
>>>>>> le vede, mentre per le radio Intel iwl-2/5xxx va in Kernel Panic.
>>>>>> Ho caricato una configurazione Wireless con 1AP e 1Mesh con radio
>>>>>> Atheros e tutte le "option disabled '0'" ma non trasmette nulla, il kernel
>>>>>> non dà errori e carica le configurazioni correttamente, nel pomeriggio
>>>>>> provo ad abilitare una sola interfaccia radio AP o Client e poi ti
>>>>>> riferisco ...
>>>>>> ho notato che gzip non funziona và spesso in crash out-of-memory e
>>>>>> che il carico CPU è molto alto, top non mi rivela nessun carico strano
>>>>>> mentre loadavg inizia ad 1.8 in avvio e scende ad 1.1 dopo una decina di
>>>>>> minuti, normalmente con il firmware linux di mikrotik il carico CPU resta
>>>>>> basso se non attivi quasi nulla.
>>>>>> Penso che dovresti compilare ancora un kernel con solo le opzioni
>>>>>> indispensabili, ti mando sempre questo pomeriggio il CONFIG di quello che
>>>>>> ritengo indispensabile e ti faccio sapere se la radio trasmette ...
>>>>>>
>>>>>> Mandi Filippo
>>>>>>
>>>>>> ----- Messaggio originale -----
>>>>>> Da: "Luca Postregna" <luca.postregna at gmail.com>
>>>>>> A: "Filippo Madaro" <filippo.madaro at gmail.com>, iuliinet at ml.ninux.org
>>>>>> Inviato: Giovedì, 4 luglio 2013 14:41:35
>>>>>> Oggetto: Re: Firmware RB133
>>>>>>
>>>>>>
>>>>>> c'era qualche problema con la branca stabile di a.a. su rb133c.
>>>>>> ho quindi scaricato, compilato, e testato un firmware direttamente
>>>>>> dal trunk.
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> *
>>>>>> https://dl.dropboxusercontent.com/u/8635572/IuliiNet/firmware/md5sums.txt
>>>>>> *
>>>>>> https://dl.dropboxusercontent.com/u/8635572/IuliiNet/firmware/openwrt-adm5120-rb1xx-rootfs.tar.gz
>>>>>> *
>>>>>> https://dl.dropboxusercontent.com/u/8635572/IuliiNet/firmware/openwrt-adm5120-rb1xx-vmlinux.elf
>>>>>>
>>>>>>
>>>>>> @filippo, fammi sapere se hai risolto, da me tutto ok
>>>>>>
>>>>>>
>>>>>> LP
>>>>>>
>>>>>>
>>>>>>
>>>>>> 2013/7/3 Filippo Madaro < filippo.madaro at gmail.com >
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> ok e se puoi mandami una immagine del rootfs.tar.gz recente ne ho una
>>>>>> Kamikaze ed una Backfire ma nessuna Attitude ...
>>>>>>
>>>>>>
>>>>>> Grazie Filippo
>>>>>>
>>>>>>
>>>>>>
>>>>>> Il giorno 03 luglio 2013 18:46, Luca Postregna <
>>>>>> luca.postregna at gmail.com > ha scritto:
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> uhm. io ho testato solo su rb133c, sto ricompilando le immagini,
>>>>>> quando è su dropbox ti avviso.
>>>>>> LP
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> 2013/7/3 Filippo Madaro < filippo.madaro at gmail.com >
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> Sei sicuro che vada su RB133c ??? a me dá errore compilato senza
>>>>>> emulazione FPU (soft-float)
>>>>>>
>>>>>>
>>>>>>
>>>>>> [ 1.772000] Creating 2 MTD partitions on "gen_nand":
>>>>>> [ 1.780000] 0x000000000000-0x000000400000 : "kernel"
>>>>>> [ 1.792000] 0x000000400000-0x000004000000 : "rootfs"
>>>>>> [ 1.812000] mtd: partition "rootfs" set to be root filesystem
>>>>>> [ 1.820000] ADM5120 built-in ethernet switch driver version 0.1.1
>>>>>> [ 1.864000] adm5120_wdt: Watchdog Timer version 0.1
>>>>>> [ 1.872000] TCP cubic registered
>>>>>> [ 1.876000] NET: Registered protocol family 17
>>>>>> [ 1.880000] 8021q: 802.1Q VLAN Support v1.8
>>>>>> [ 1.892000] yaffs: dev is 32505859 name is "mtdblock3" ro
>>>>>> [ 1.896000] yaffs: passed flags ""
>>>>>> [ 2.744000] VFS: Mounted root (yaffs2 filesystem) readonly on device
>>>>>> 31:3.
>>>>>> [ 2.752000] Freeing unused kernel memory: 160k freed
>>>>>> [ 3.248000] FPU emulator disabled, make sure your toolchain was
>>>>>> compiled with software floating point support (soft-float)
>>>>>>
>>>>>>
>>>>>> la scheda é una RB112 con CPU ADM5120 se invece installo kernel +
>>>>>> rootfs Kamikaze vá tutto ma vorrei una versione recente tipo Attitude
>>>>>>
>>>>>>
>>>>>> Mandi Filippo
>>>>>>
>>>>>>
>>>>>>
>>>>>> Il giorno 03 luglio 2013 17:58, Filippo Madaro <
>>>>>> filippo.madaro at gmail.com > ha scritto:
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> Mi manca il file system openwrt-adm5120-rb1xx-rootfs.tar.gz
>>>>>> ho quello vecchio della versione Kamikaze ma non l'ultimo
>>>>>>
>>>>>>
>>>>>> Ciao Filippo
>>>>>>
>>>>>>
>>>>>>
>>>>>> Il giorno 03 luglio 2013 12:12, Luca Postregna <
>>>>>> luca.postregna at gmail.com > ha scritto:
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> Gdrive, Mega e simile preferisco non usarli, non dispongono di un
>>>>>> link diretto per il download. Diversamente, per dropbox tutto ok.
>>>>>>
>>>>>>
>>>>>> Ecco i files per le rb133x:
>>>>>>
>>>>>>
>>>>>> *
>>>>>> https://dl.dropboxusercontent.com/u/8635572/IuliiNet/firmware/md5sums.txt
>>>>>> *
>>>>>> https://dl.dropboxusercontent.com/u/8635572/IuliiNet/firmware/openwrt-adm5120-rb1xx-vmlinux.bin
>>>>>> *
>>>>>> https://dl.dropboxusercontent.com/u/8635572/IuliiNet/firmware/openwrt-adm5120-rb1xx-vmlinux.elf
>>>>>>
>>>>>> le istruzione per il flash delle rb133c le puoi trovare alla pagina
>>>>>> http://iulii.net/firmware.html#rb133c
>>>>>> Se non ricordo male, questi binari contengono i moduli ath5k, forse
>>>>>> anche ath9k. Firewall, dnsmasq, pppoe, credo di averli rimossi.
>>>>>> Per un buggetto nella conf di default al primo boot trovi l'esempio
>>>>>> per una rb1xx con 4 porte switch. Comunque, nel link sopra trovi una
>>>>>> configurazione funzionante per rb133c.
>>>>>>
>>>>>>
>>>>>> per quello che riguarda miniPCI 802.11n non ho recuperato alcun
>>>>>> modello. Ho solo una b/g che mi ha passato Emanuele che utilizzo con
>>>>>> l'antenna di un portatile.
>>>>>>
>>>>>>
>>>>>> Saluti
>>>>>> LP
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> 2013/7/3 Filippo Madaro < filippo.madaro at gmail.com >
>>>>>>
>>>>>>
>>>>>> Ciao Luca, ho cercato invano di scaricare i tre file per le RB133 da
>>>>>> downloads.iulii.net ... non si apre il sito a noi poveri sfigati
>>>>>> IPV4 ... li puoi postare su Gdrive / Dropbox / Mega che ho un paio di
>>>>>> schede da flashare.
>>>>>>
>>>>>> Per le miniPCI 802.11n hai poi trovato qualcosa di compatibile
>>>>>> OpenWRT e con quante antenne 1/2/3 e quanti TX/RX 2T2R 3T3R ???
>>>>>>
>>>>>> Mandi Filippo
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> --
>>>>>>
>>>>>> luca.postregna.name
>>>>>> twitter.com/lucapost
>>>>>>
>>>>>>
>>>>>>
>>>>>> --
>>>>>>
>>>>>>
>>>>>> p.i. Filippo Madaro
>>>>>>
>>>>>> Mob. 3883448904
>>>>>> Consulente DUE Energie
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> --
>>>>>>
>>>>>>
>>>>>> p.i. Filippo Madaro
>>>>>>
>>>>>> Mob. 3883448904
>>>>>> Consulente DUE Energie
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> --
>>>>>>
>>>>>> luca.postregna.name
>>>>>> twitter.com/lucapost
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> --
>>>>>>
>>>>>>
>>>>>> p.i. Filippo Madaro
>>>>>>
>>>>>> Mob. 3883448904
>>>>>> Consulente DUE Energie
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> --
>>>>>>
>>>>>> luca.postregna.name
>>>>>> twitter.com/lucapost
>>>>>>
>>>>>
>>>>>
>>>>>
>>>>> --
>>>>> luca.postregna.name
>>>>> twitter.com/lucapost
>>>>>
>>>>
>>>>
>>>>
>>>> --
>>>> luca.postregna.name
>>>> twitter.com/lucapost
>>>>
>>>
>>>
>>>
>>> --
>>> p.i. *Filippo Madaro*
>>> Mob. 3883448904
>>> Consulente DUE Energie <http://www.dueenergie.com/index.html>
>>>
>>>
>>
>>
>> --
>> luca.postregna.name
>> twitter.com/lucapost
>>
>
>
>
> --
> p.i. *Filippo Madaro*
> Mob. 3883448904
> Consulente DUE Energie <http://www.dueenergie.com/index.html>
>
>
--
luca.postregna.name
twitter.com/lucapost
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://ml.ninux.org/pipermail/iuliinet/attachments/20130707/2cf26371/attachment-0001.html>
More information about the IuliiNet
mailing list